Items for Faculty/School / Institute/Centre :
Current - Faculty of Health, Engineering and Sciences - No Department (1 Jul 2013 -)

2022

Schuster, Robert (2022) Airborne Observation Controller. [USQ Project]

Wyper, Rye (2022) Benefits and Challenges of Applying Travelling Wave Technology to Sub-transmission Networks. [USQ Project]

Coonan, Tom (2022) A New Supplementary Binder in Foamed Bitumen Stabilisation. [USQ Project]

Coogan, Tim (2022) A Water Sensitive Urban Design approach to mitigate the effects of Rainfall Derived Infiltration and inflow on existing sewerage systems. [USQ Project]

Keenan, Mike (2022) Bridge load assessment using machine learning and weigh-in-motion data. [USQ Project]

Armanasco, Matthew (2022) Cardiac Biometric Authentication Using Channel State Information. [USQ Project]

Gough, Tom (2022) Compressive Behaviour of Short Engineered Cementitious Composite Columns Containing Recycled Polyethylene Terephthalate Aggregate. [USQ Project]

Fritz, Patrick (2022) Design Analysis of Guy Wires of Communication Towers: Industry Based Project Proposed by Raytheon Australia. [USQ Project]

Sharpe, Kyal (2022) Development of Smart Sewer Pipeline Fault Detection Method using CCTV Inspection Data and Deep Learning. [USQ Project]

Perkins, Shaun (2022) Evaluation of Issues Affecting Stabilised Granular Pavements. [USQ Project]

Sheehan, Michael (2022) Fabrication and design of a Stirling Engine powered by hydrogen. [USQ Project]

O'Keeffe, Myles E. (2022) Feasibility of using Thermoelectric Generators to Improve Fuel Efficiency in Existing In-service Vehicles. [USQ Project]

Denman, Michael (2022) Identifying the Types and Causes of Construction Defects in Multi-Unit Dwellings. [USQ Project]

Green, Sam (2022) Investigation into implement status awareness for autonomous tractors. [USQ Project]

Sale, Maggie (2022) Lessons Learnt from Bridge Reconstructions Post Successive Disaster Events in the Eurobodalla LGA. [USQ Project]

Bischof, Lachlan (2022) Off-Highway Platooning Sensor Selection and Survivability. [USQ Project]

Baker, Ted (2022) Optimisation of a Hydro-Pneumatic Accumulator using Computational Fluid Dynamics. [USQ Project]

Shrestha, Nabin (2022) Remote Controlled Motorised Laser Alignment Trolley. [USQ Project]

Faivre, Yohanne (2022) SPT - CPT Correlation in South East Queensland, Australia. [USQ Project]

Di Mauro, Matthew N. (2022) The Comparative Analysis of the Design of Shredder Hammer Tips and Bars in Sugar Milling Applications. [USQ Project]

Hall, Nick (2022) Unsealed Road Grading Techniques. [USQ Project]

2020

Qalilawa, Peter William Edward (2020) The use of model software that incorporates pressure-reducing valves in the Suva-Nausori Water Distribution System to minimize water disruption. [USQ Project]

2019

Weedon, Brent (2019) Design and implentation of axial-flux permanent magnet machine for use in wind turbine applications. [USQ Project]

Armstrong, David (2019) Smart Model/Package for Home Based Solar Grid System Design. [USQ Project]

2018

Herbert, James Feleciano (2018) An Instrumented Approach to the Classification of Alcoholic Beverages: Combining PTR-ToF Mass Spectrometry, with Machine Learning. [USQ Project]

Alwazzan, Essa (2018) Effect of fibre content on compressive and flexural properties of coconut fibre reinforced epoxy composites. [USQ Project]

Veivers, Shannon (2018) Fault Analysis of Vision System on Autonomous Blast Hole Drills. [USQ Project]

O'Sullivan, Kyra (2018) Soil physical and chemical properties as effected by long-term land application of paunch. [USQ Project]

Bell, Mark (2018) Transient Behaviour of Three Phase STATCOMs. [USQ Project]

Ryan, Brendan (2018) Wave Gauge: Characterising vessel movements and their erosive components. [USQ Project]

2017

Hancock, Jarred (2017) The Development of Building a Cadet Training Manual. [USQ Project]

Wellings, Mansell (2017) The effect of high powered ultrasonic treatment on an Australian anaerobic digester. [USQ Project]

Batra, Ankur (2017) Fracture of Natural Fibre Composites. [USQ Project]

2015

Alajmi, Faisal (2015) Study on tribological performance of mild steel under canola bio-lubricant conditions. [USQ Project]